Skip to content
Kempenfelt Bay Garage Door Co.Request a visit
Open 24/7(249) 315-4741Call now
Person holding metal bars beside exposed coiled springs above a garage door. — Torsion Spring Replacement, Tollendal

Emergency Springs · Tollendal

Torsion Spring Replacement in Tollendal

Looking up at the coil above the door, you can see a clean split with a gap of several centimetres between the two halves. The rest of the spring looks fine, but the door has become almost impossible to move by hand.

Call now · open 24/7(249) 315-4741

Request a visit

Right now

Before the door is looked at

Call (249) 315-4741, open 24/7.

  1. When a spring breaks, the safe approach for the household is to leave the door where it is, keep people and vehicles clear, and avoid running the opener, which can damage the top section, the trolley or the gear drive.

  2. Pull the manual release only when the door is fully closed unless a technician asks otherwise; a door disconnected while partly open can move on its own if the springs are out of balance.

  3. Never drive a vehicle at a closed door to get out; the door collapses and the stored tension in the counterbalance is released. Use the release, the outside key release, or a technician.

In plain words

The finished result is a door that behaves the way a good garage door should: it lifts by hand with light effort, stays where you leave it at mid-height, closes softly and lets the opener run with little strain. Reaching that point involves measuring the door, choosing a matched spring, winding it to the correct turns and testing the balance through the full travel. The technician then runs the opener's reversal test and lubricates the moving parts. You are left with a record of the spring installed, so future service starts from known specifications.

Sound familiar?

After pulling the red release cord, you tried lifting the door yourself and it would barely leave the floor. A door that used to glide up with one hand now takes real effort, which points to the counterbalance rather than the opener.

How the visit goes

Torsion Spring Replacement · Tollendal

How the visit goes

Technician at a blue ladder working under a black and white opener, with a red pull cord hanging beside it. — Tollendal
  1. 1

    Confirming the system layout

    Doors are set up in several ways, and the replacement has to match. The technician notes whether there is one spring or two, whether the shaft is a single piece or two halves joined by a coupler, and what the shaft diameter is. Drum type is read from the drums themselves: standard-lift drums for a normal ceiling, high-lift or vertical-lift drums where the door rises well above the opening, or a rear-mounted assembly in a low-headroom garage. Track radius and headroom are measured because they change how many turns the spring needs and which drums it must work with.

  2. 2

    Fitting a matched pair

    On a two-spring door the springs are installed as a set: one left-wound and one right-wound, mirrored on either side of the centre bracket, with matching wire size, diameter and length so each carries half the load. Both stationary cones bolt to the centre bracket and both winding cones face outward. The technician winds each spring the same number of quarter turns, alternating between them, so the shaft is never loaded unevenly. Once both are set, the door is balanced and tested as one system. Equal springs mean equal wear, so the pair reaches the end of its life together rather than one after the other.

  3. 3

    What cycle life means for you

    The spring you chose is rated for a number of full open-close cycles, and that number translates into years according to your routine. A standard-cycle spring on a door used four times a day works out to several years of service; a household with teenagers and a home workshop will use cycles sooner, while a high-cycle spring stretches the same routine considerably further. Knowing your rating and your habits gives you a rough sense of when the next replacement falls due, so spring service becomes a planned item like furnace maintenance rather than a surprise on a cold morning.

In the van

  • Centre bearing bracket and bearing
  • Stationary cone bolts and nuts
  • Locking pliers for the track
  • Cable drums
  • Wire gauge and tape measure

What affects the quote

  1. 1

    One spring or two

    A single-spring door needs one spring; a paired system is usually replaced as a matched set of left- and right-wound springs. The number of springs and whether both are replaced is the largest single influence on the scope.

  2. 2

    Oversize or non-standard doors

    Very wide doors, tall doors, carriage-house doors with heavy overlays and light-commercial doors may need duplex springs, multiple springs or larger drums, which changes both the hardware and the method.

  3. 3

    Centre and end bearings

    With the shaft out, bearings that grind, wobble or have seized are renewed. Smooth bearings reduce the load on the spring and opener, and their condition is confirmed by hand during the check.

Same fees day, night or weekend.

Have it ready

Before you call · 0 / 3

(249) 315-4741

Torsion Spring Replacement: questions

Advice · (249) 315-4741

What other parts are often replaced with the spring?

The shaft is free during a spring change, which makes it the natural time to renew the centre bearing and end bearings if they grind or wobble. Lift cables that show fraying or rust at the bottom brackets are replaced so the new spring pulls on sound steel, and cracked or worn drums are swapped. On older doors, a corroded centre bracket or loose lag bolts may also be addressed. Each item is shown and explained before it is added.

Why do springs seem to break in cold weather?

Cold makes steel slightly less forgiving and thickens the grease on the coils, so a spring that has already used most of its cycle life is more likely to let go on a frosty morning when the door is first opened. The cold is the final straw rather than the cause; the underlying reason is fatigue from years of cycles, sometimes helped along by rust and dry coils.

Why does the door need to be balanced, and how is that tested?

Balance means the spring is holding almost exactly the door's weight, so the door neither flies up nor slams down and the opener only guides it. It is tested by releasing the opener, lifting the door to about waist height and letting go: a balanced door stays there. The technician fine-tunes in quarter turns of the spring until the door holds at several heights and travels evenly on both sides.

Torsion Spring Replacement near you

Simcoe, Ontario

Tollendal information

Town
Tollendal, Simcoe, Ontario
In business
22 years
Hours
Open 24/7 · nights, weekends and holidays, same fees
Visits
On-site assessment preferred. Request a visit or call.

What the census means at the door

29%

Newer homes. About 29% of homes in Barrie were built in 1980 or earlier, according to the 2021 Census.

Newer houses often have a double door over a two-car garage, which means a heavier door, a pair of torsion springs and cables that must be matched exactly. Replacing springs on these doors is done in pairs so the door lifts level and the opener is not fighting one side.

58%

A mix of homes. Single-detached houses make up about 58% of homes in Barrie (2021 Census).

In mixed neighbourhoods, noise matters differently from one address to the next. A detached house with a bedroom above the garage and a townhouse with a neighbour through the wall both benefit from a belt-drive opener and nylon rollers, and we explain the difference either way.

Source: Statistics Canada, 2021 Census of Population

Open Tollendal in Google Maps

Open 24/7

Request a visit

Looking up at the coil above the door, you can see a clean split with a gap of several centimetres between the two halves.

Call now · open 24/7(249) 315-4741
  • On-site assessment preferred
  • Same fees day, night or weekend
  • 22 years in business